TM 5-3895-376-14&P
(3) Items that are included in kits and sets are
(2) FIG. column. This column lists the number
listed below the name of the kit or set on Figure KIT.
of the Figure where the item is identified/located. The
figures are in numerical order in Section II and Sec-
tion III.
(4) Spare/repair parts that make up an assem-
bled item are listed immediately following the assem-
bled item line entry.
(3) ITEM column. The item number identifies
the item associated with the figure listed in the adja-
cent FIG. column. This item is also identified by the
(5) Part numbers for bulk materials are refer-
NSN listed on the same line.
enced in this column in the line item entry for the item
to be manufactured/fabricated.
b. PART NUMBER INDEX. Part numbers in this
index are listed by part number in ascending alphanu-
(6) When the item is not used with all serial num-
meric sequence (i.e., vertical arrangement of letter
bers of the same model, the effective serial numbers
and number combination which places the first letter
are shown on the last line(s) of the description (before
or digit of each group in order A through Z, followed
UOC). Not applicable.
by the numbers 0 through 9 and each following letter
or digit in like order).
(7) The usable on code, when applicable (see
paragraph 5, Special information).
(1) CAGEC column. The Commercial And Gov-
ernment Entity (CAGE) Code (C) is a 5-digit alphanu-
(8) In the Special Tools List section, the basis of
meric code used to identify the manufacturer,
issue (BOI) appears as the last line(s) in the entry for
distributor, or Government agency, etc., that supplies
each special tool, special TMDE, and other special
the item.
support equipment. When density of equipments sup-
ported exceeds density spread indicated in the basis
(2) PART NUMBER column. Indicates the pri-
of issue, the total authorization is increased propor-
mary number used by the manufacturer (individual,
tionately.
firm, corporation, or Government activity), which con-
trols the design and characteristics of the item by
(9) The statement "END OF FIGURE" appears
means of its engineering drawings, specifications,
just below the last item description in Column 5 for a
standards, and inspection requirements to identify an
given figure in both Section II and Section III.
item or range of items.
f. QTY (Column (6)). The QYT (quantity per figure
(3) STOCK NUMBER column. This column lists
column) indicates the quantity of the item used in the
the NSN for the associated part number and manufac-
breakout shown on the illustration figure, which is pre-
turer identified in the PART NUMBER and CAGEC
pared for a functional group, subfunctional group, or
columns to the left.
an assembly. A "V" appearing in this column in lieu of
a quantity indicates that the quantity is variable and
(4) FIG. column. This column lists the number
the quantity may vary from application to application.
of the figure where the item is identified/located in
Section II and III.
C-4. Explanation of Columns (Section IV).
a. NATIONAL STOCK NUMBER (NSN) INDEX.
(5) lTEM column. The item number is that num-
ber assigned to the item as it appears in the figure ref-
erenced in the adjacent figure number column.
(1) STOCK NUMBER column. This column lists
the NSN by National item identification number (NIIN)
sequence. The NIIN consists of the last nine digits of
c. FIGURE AND ITEM NUMBER INDEX.
NSN
the NSN (i.e., 5305-01-674-1467). When using this
(1) FIG. column. This column lists the number
of the figure where the item is identified/located in
column locate an item, ignore the first 4 digits of the
Section II and III.
NSN. However, the complete NSN should be used
when ordering items by stock number.
C-4
