TM 5-3815-224-14&P
f.
QTY (Column (6)). The QTY (quantity per figure
column) Indicates the quantity of the item used in the
breakout shown on the illustration/figure, which is
prepared for a functional group, subfunctional group, or
an assembly. A "V" appearing in this column in lieu of a
quantity indicates that the quantity is variable and the
quantity may vary from application to application.
4.
Explanation of Columns (Section IV).
a.
NATIONAL STOCK NUMBER (NSN) INDEX.
(1)
STOCK NUMBER column. This column
lists the NSN by National Item Identification Number
(NIIN) sequence. The NIIN consists of the last nine
NSN
_______|_______
digits of the NSN (i.e., 5305-01-674-1467). When using
|
NIIN
this column to locate an item, ignore the first 4 digits of
the NSN. However, the complete NSN should be used
when ordering items by stock number.
(2)
FIG. column. This column lists the
number of the figure where the item is identified/located.
The figures are in numerical order in Section II and
Section III.
(3)
ITEM column. The item number identifies
the item associated with the figure listed in the adjacent
FIG. column. This item is also identified by the NSN
listed on the same line.
b.
PARTNUMBER INDEX. Part numbers in this
index
are
listed
by
part
number
in
ascending
alphanumeric sequence (i.e., vertical arrangement of
letter and number combination which places the first
letter or digit of each group in order A through Z, followed
by the numbers 0 through 9 and each following letter or
digit in like order).
(1)
CAGEC column. The Commercial and
Government Entity (CAGE) Code (C) is a 5-digit
alphanumeric code used to identify the manufacturer,
distributor, or Government agency, etc., that supplies the
item.
(2)
PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation, or Government activity), which controls
the design and characteristics of the item by means of its
engineering drawings, specifications standards, and
inspection requirements to identify an item or range of
items.
(3)
STOCK NUMBER column. This column
lists the NSN for the associated part number and
manufacturer identified in the PART NUMBER and
CAGE columns to the left.
(4)
FIG. column. This column lists the
number of the figure where the item is identified/located
in Sections II and 111.
(5)
ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
c.
FIGURE AND ITEM NUMBER INDEX.
(1)
FIG. column. This column lists the
number of the figure where the item is identified/located
in Sections II and III.
(2)
ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
(3)
STOCK NUMBER column. This column
lists the NSN for the item.
(4)
CAGEC column. The Commercial and
Government Entity (CAGE) Code (C) is a 5-digit
alphanumeric code used to identify the manufacturer,
distributor, or Government agency, etc., that supplies the
item.
(5)
PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation, or Government activity), which controls
the design and characteristics of the item by means of its
engineering drawings, specifications standards and
inspection requirements to identify an item or range of
items.
5.
Special Information.
a.
USABLE ON CODE. The usable on code
appears in the lower left corner of the Description column
heading. Usable on codes are shown as "UOC:
" in the Description column (justified left) on the first
line following applicable item description/ nomenclature.
Uncoded items are applicable to all models. Identifi-
cation of the usable on codes used in the RPSTL are:
Code
Used On
CCN
Boom Extension (10 ft)
CCQ
Boom Jib (15 ft)
b.
FABRICATION INSTRUCTIONS. Bulk materials
required to manufacture items are listed in the Bulk
Material Functional Group of this RPSTL. Part numbers
for bulk materials are also referenced in the Description
column of the line item entry for the item to be
manufactured/fabricated.
Detailed
fabrication
instructions for items source coded to be manufactured
or fabricated are found in TM 5-3810-303-24.
c.
KITS. Line item entries for repair parts kits
appear in group 9401 in Section II. Not Applicable.
d.
INDEX NUMBERS. Items which have the word
BULK in the figure column will have an index number
shown in the item number column. This index number is
a
cross-reference
between
the
National
Stock
Number/Part Number Index and the bulk material list in
Section II.
Change 1 C-4
